Instalación Básica Ontap 9

Este documento describe el Setup Básico de una AFF8040 en Cluster con ONTAP 9, realmente da igual la controladora que sea, el proceso es el mismo para todas las cabinas con la misma versión.

La tarea fundamental del proceso de setup es la de configurar correctamente los interfaces de red del sistema, otorgar un nombre de máquina al almacenamiento y configurar la resolución de nombres en la controladora.

Conectarse por cable serial

Establecer una conexión Hyperteminal con la siguiente configuración:
      • Speed: 9600
      • Data bits: 8
      • Stop bits: 1
      • Paridad: Ninguno (none)
      • Flow control: Ninguno (none)

Setup Nodo-01

Una vez pinchado el puerto Serial sobre la primera controladora comienza el proceso que se muestra a continuación:
Exiting the cluster setup wizard. Any changes you made have been saved.
The cluster administrator's account (username "admin") password is set to the system default.
Warning: You have exited the cluster setup wizard before completing all
of the tasks. The cluster is not configured. You can complete cluster setup by typing
"cluster setup" in the command line interface.

Escribir el siguiente comando para comenzar la creación de clúster.
::> cluster setup

Welcome to the cluster setup wizard.
You can enter the following commands at any time:
      "help" or "?" - if you want to have a question clarified,
      ""back" - if you want to change previously answered questions, and
      ""exit" or "quit" - if you want to quit the cluster setup wizard.
        "Any changes you made before quitting will be saved.

You can return to cluster setup at any time by typing "cluster setup".
To accept a default or omit a question, do not enter a value.

Se va a proceder a la creación del clúster:
Do you want to create a new cluster or join an existing cluster? {create, join}: create

Do you intend for this node to be used as a single node cluster? {yes, no} [no]: Enter

En este apartado como no se tiene Switch para formar el cluster el modo de conexión va a ser directo entre los dos nodos, por eso se selecciona esta forma
Will the cluster network be configured to use network switches? [no]: No
Existing cluster interface configuration found:
Port MTU IP Netmask
e0a 9000 169.254.80.198 255.255.0.0
e0b 9000 169.254.1.51 255.255.0.0
e0c 9000 169.254.31.83 255.255.0.0
e0d 9000 169.254.15.146 255.255.0.0

Do you want to use this configuration? {yes, no} [yes]: yes

Enter the cluster administrator's (username "admin") password: Password
Retype the password: Password

Step 1 of 5: Create a Cluster
You can type "back", "exit", or "help" at any question.

Introducir el nombre del clúster
Enter the cluster name: AroundCluster Enter the cluster base license key:
Se puede introducir ahora o después.

Comienza la creación del clúster
Creating cluster AroundCluster
Network set up
Network set up .
Network set up ..
Network set up ...
Network set up ....
Network set up .....
Network set up ......
Network set up .......
Network set up ........
Network set up .........
Network set up ..........
Network set up ...........
Network set up ............
Network set up .............
Network set up ..............
Starting replication service
Starting replication service .
Creating cluster
System start up
System start up .
System start up ..
System start up ...
System start up ....
System start up .....
System start up ......
Starting cluster support services
Cluster AroundCluster has been created.

Step 2 of 5: Add Feature License Keys You can type "back", "exit", or "help" at any question. Enter an additional license key []: Se puede introducir ahora o después.

Step 3 of 5: Set Up a Vserver for Cluster Administration
You can type "back", "exit", or "help" at any question.

Hay que seleccionar el Puerto para la interface de administración del clúster, para no gastar más puerto seleccionamos el de administración, el e0M y configuramos su direccionamiento.

Enter the cluster management interface port: e0M
Enter the cluster management interface IP address: 10.0.0.10
Enter the cluster management interface netmask: 255.255.255.0
Enter the cluster management interface default gateway: 10.0.0.254

A cluster management interface on port e0M with IP address 10.1.0.120 has been created. You can use this address to connect to and manage the cluster.

Warning: You have exited the cluster setup wizard before completing all
of the tasks. The cluster is not configured. You can complete cluster setup by typing
"cluster setup" in the command line interface.

Introducir el nombre y el servidor para el DNS
Enter the DNS domain names: AroundStorage.local
Enter the name server IP addresses: 10.0.0.31
DNS lookup for the admin Vserver will use the AroundStorage.local domain.

Step 4 of 5: Configure Storage Failover (SFO)
You can type "back", "exit", or "help" at any question.
SFO will be enabled when the partner joins the cluster.
Step 5 of 5: Set Up the Node
You can type "back", "exit", or "help" at any question.

Where is the controller located []:
AroundStorage Site Spain

Seleccionar la interface de administración, como antes seleccionaremos la e0M y configuraremos su direccionamiento.
Enter the node management interface port [e0M]: e0M
Enter the node management interface IP address: 10.0.0.11
Enter the node management interface netmask: 255.255.255.0
Enter the node management interface default gateway: 10.0.0.254

This system will send event messages and weekly reports to NetApp Technical Support.
To disable this feature, enter "autosupport modify -support disable" within 24 hours.
Enabling AutoSupport can significantly speed problem determination and resolution should a problem occur on your system.
For further information on AutoSupport, please see: http://support.netapp.com/autosupport/
Press enter to continue:

To complete cluster setup, you must join each additional node to the cluster
by running "cluster setup" on each node.

Once all nodes have been joined to the cluster, see the Clustered Data ONTAP
Software Setup Guide for information about additional system configuration
tasks. You can find the Software Setup Guide on the NetApp Support Site.

To complete system configuration, you can use either OnCommand System Manager
or the Data ONTAP command-line interface.

To access OnCommand System Manager, point your web browser to the cluster
management IP address (10.0.0.10).
To access the command-line interface, connect to the cluster management
IP address (for example, ssh admin@10.0.0.10).

Una vez finalizada la creación del clúster, verificar el clúster como se muestra a continuación.
AroundCluster::> cluster show
Node                     Health   Eligibility
--------------------- ------- ------------
AroundCluster-01     true     true


Setup Nodo-01

Se va a proceder agregar el Segundo nodo al clúster. Configurar el direccionamiento del nodo169.254.125.62 Type yes to confirm and continue {yes}: yes

Enter the node management interface port: e0M
Enter the node management interface IP address: 10.0.0.12
Enter the node management interface netmask: 255.255.255.0
Enter the node management interface default gateway: 10.0.0.254

A node management interface on port e0M with IP address 10.0.0.12 has been created.
This node has its management address assigned and is ready for cluster setup.
To complete cluster setup after all nodes are ready, download and run the System Setup utility from the NetApp Support Site and use it to discover the configured nodes.

For System Setup, this node's management address is: 10.0.0.254.
Alternatively, you can use the "cluster setup" command to configure the cluster.

login:
admin
******************************************************
* This is a serial console session. Output from this *
* session is mirrored on the SP console session. *
******************************************************
::>


Escribir el siguiente comando para agregar el nodo al Clúster
::> cluster setup

Welcome to the cluster setup wizard.
You can enter the following commands at any time:
      "help" or "?" - if you want to have a question clarified,
      "back" - if you want to change previously answered questions, and
      "exit" or "quit" - if you want to quit the cluster setup wizard.
         Any changes you made before quitting will be saved.

You can return to cluster setup at any time by typing "cluster setup".
To accept a default or omit a question, do not enter a value.


Agregar el nodo.
Do you want to create a new cluster or join an existing cluster? {create, join}: Join